Copyright Digital Equipment Corp. All rights reserved.
Examples
1.$ SUBMIT /PARAMETERS=(TXT,DOC,MEM) BACKUP, AVERAGE, RUNMASTER
Job BACKUP (queue SYS$BATCH, entry 416) pending
In this example, the SUBMIT command enters three command
procedures in a single job. The job is given three parameters:
P1 is equated to the string TXT, P2 to the string DOC, and P3
to the string MEM. After the procedure BACKUP.COM is executed,
the procedures AVERAGE.COM and RUNMASTER.COM are executed.
2.$ SUBMIT/NAME=BATCH24/HOLD TESTALL
Job BATCH24 (queue SYS$BATCH, entry 467) holding
In this example, the SUBMIT command enters the procedure
TESTALL.COM as a batch job and specifies that the job be held
for later processing. The job is not released until the SET
ENTRY/RELEASE command is entered. The /NAME qualifier requests
that the batch job be identified as BATCH24.
3.$ SUBMIT TEST.COM
Job TEST (queue SYS$BATCH, entry 493) pending
$ BATCH_JOB = $ENTRY
.
.
.
$ DELETE/ENTRY='BATCH_JOB'
In this command sequence, the $ENTRY symbol is used to refer to
a particular job in the queue file. The SUBMIT command creates
a batch job to run the command procedure TEST.COM. In addition,
the SUBMIT command defines $ENTRY as a local symbol whose
value is the entry number of the job (493 in this example).
The second statement assigns the value $ENTRY to the local
symbol BATCH_JOB. The last line of the example deletes the job
by using the symbol BATCH_JOB to identify it.
4.$ DEFINE JUNE WORKZ:[SCHREURS]ANNUAL_REPORT.COM
$ SUBMIT JUNE
Job ANNUAL_REPORT (queue SYS$BATCH, entry 229) started on ZOO_BATCH
In this example, the logical name JUNE is created and equated
to ANNUAL_REPORT.COM with the DEFINE command. Using the logical
name JUNE, the user submits ANNUAL_REPORT.COM to the batch
queue. Note that the system translates the logical name JUNE
to ANNUAL_REPORT.COM before ANNUAL_REPORT.COM is submitted
to the batch queue. Also, the log file produced is named
ANNUAL_REPORT.COM rather than JUNE.COM.
Note also that the job is submitted to the generic queue
SYS$BATCH, but runs on the execution queue ZOO_BATCH.
5.$ SUBMIT/HOLD/QUEUE=ANYRADQ /RAD=1 TEST.COM
Job TEST (queue ANYRADQ, entry 23) holding
$ SHOW ENTRY/FULL 23
Entry Jobname Username Blocks Status
----- ------- -------- ------ ------
23 TEST SYSTEM Holding
On idle batch queue ANYRADQ
Submitted 24-JUL-2001 14:19:37.44 /KEEP /NOPRINT /PRIORITY=100
/RAD=0
File: _$1$DKB200:[SWEENEY.CLIUTL]TEST.COM;1
In this example, TEST.COM is submitted to the queue ANYRADQ.
There is no RAD setting on the ANYRADQ queue.
6.$ SUBMIT/HOLD/QUEUE=BATCHQ1 /RAD=1 TEST.COM
Job TEST (queue BATCHQ1, entry 24) holding
$ SHOW ENTRY 24/FULL
Entry Jobname Username Blocks Status
----- ------- -------- ------ ------
24 TEST SYSTEM Holding
On idle batch queue BATCHQ1
Submitted 24-JUL-2001 14:23:10.37 /KEEP /NOPRINT /PRIORITY=100
/RAD=0
File: _$1$DKB200:[SWEENEY.CLIUTL]TEST.COM;2
In this example, the queue, BATCHQ1, is defined with /RAD=0.
Therefore, use of the SUBMIT command creates a job that runs on
RAD 0, even though RAD 1 was specified.