Qualifiers

 

/ADDRESS_COMPRESSION
   Indicates whether the address compression is on or off.
 

/ALL
      /ALL[=BRIEF] (default)
      /ALL[=LONG]

   Displays all the current device and communication settings. BRIEF
   formats the output for the screen. LONG displays each setting on
   a separate line.
 

/COUNTERS
      /COUNTERS=(keyword,...)

   Shows the current values for the specified counter(s). You
   can specify one or more of the following keywords with this
   qualifier:

   Keyword          Description

   ALL              Displays all counters.
   BAD_FCS_PACKETS  Displays the count of packets with bad frame
                    check sequence (FCS).
   DATA_LOST        Displays the count of lost characters that were
                    reported by hardware.
   DROPPED_         Displays the count of all characters thrown
   CHARACTERS       away.
   FRAMING_ERRORS   Displays the count of characters with framing
                    errors.
   LONG_PACKETS     Displays the count of packets longer than the
                    current maximum receive unit setting (MRU).
   RECEIVED_        Displays the count of total packets received.
   PACKETS
   RUNT_PACKETS     Displays the count of packets with too few
                    characters.
   TOTAL_           Displays the count of all characters received.
   CHARACTERS
   TRANSMITTED_     Displays the count of total packets transmitted.
   PACKETS
 

/ECHO
      /ECHO=(FAILURE=value, INTERVAL=value)

   Specifies the number of Link Control Protocol (LCP) echo requests
   and the interval (in milliseconds) between requests that must be
   sent without response before the line is considered down.
 

/FCS_SIZE
   Shows the current receive and transmit FCS size in bits.
 

/FLOW_CONTROL
      /FLOW_CONTROL=(keyword,...)

   Shows the current flow control setting used over the asynchronous
   physical link. You can specify one of the following keywords with
   this qualifier:

   Keyword    Description

   HARDWARE   Uses RTS/CTS flow control. If using this control, the
              transmit Asynch Control Character Map (ACCM) can be
              0x0, 0x0, 0x0, 0x60000000. Only valid for lines set to
              /MODEM or /COMMSYNCH.
   XON_XOFF   Uses band flow control. If using this control, the
   (de-       optimal transmit ACCM is 0xA0000, 0x0, 0x0, 0x60000000.
   fault)     Only valid for asynchronous lines.
 

/HANGUP
   Displays the action that occurs when a session is terminated.
 

/MAGIC_NUMBER_RETRIES
   Shows the number of attempts that are made to negotiate a magic
   number.
 

/MAXCONFIGURE
   Shows the number of configure-request packets sent without
   acknowledgment before assuming that the peer is not responding.
 

/MAXFAILURE
   Displays the number of configure-nak packets sent before sending
   a configure-ack and before assuming that the configuration is not
   converging.
 

/MAXTERMINATE
   Shows the number of terminate-request packets sent without
   acknowledgment before assuming the peer is unable to respond.
 

/MRU
   Displays the largest packet that the line can receive.
 

/MTU
   Displays the largest packet that the line can transmit.
 

/NETWORK_PROTOCOL
   Displays the current network protocol(s) allowed over the
   physical link.
 

/PASSIVE
   Indicates whether this is a passive or active line.
 

/PERMANENT
   Indicates whether this is a permanent or transient (nonpermanent)
   line.
 

/PROTOCOL_COMPRESSION
   Shows the status of protocol field compression.
 

/RECEIVE_ACCM
   Displays the value of the current receive ACCM for asynchronous
   ports.
 

/RESTART_TIMER
   Displays the interval used to time transmission of request
   packets.
 

/SPEED
   Indicates the current input and output speeds of the line.
 

/TRANSMIT_ACCM
   Displays the value of the current transmit ACCM for asynchronous
   ports.