27.4.3 – MRD_STATUS_RECOVERED_ERROR
This error occurs when a SCSI device returns only a sense key
of 1h. This indicates that although a command successfully
completed, the target device had performed some internal error
recovery.
27.4.4 – MRD_STATUS_MEDIUM_ERROR
This error occurs when ASC and ASCQ are zero, but the sense key
is 3h. This occurs when the target encounters a nonrecoverable
error due to a flaw in the medium.
27.4.5 – MRD_STATUS_ROBOT_HW_ERROR
This error occurs when ASC and ASCQ are zero, but the sense key
is 4h. This occurs when the target encounters a nonrecoverable
hardware error.
27.4.6 – MRD_STATUS_ROBOT_ILLEGAL_REQUEST
This error occurs for a variety of reasons.
It is used when a sanity check fails in the code that attempts
to move a cartridge to the Pass-Through Mechanism, when the robot
type isn't a TL82n.
It is used in the mrd_lock(3mrd) code when the value is not one
of ALLOW_REMOVAL or PREVENT_REMOVAL.
It is used when the medium changer does not support the Prevent
/Allow Medium Removal command or the lock value is not one or
zero. The specific cause can be determined by examining the ASC
/ASCQ values in the status data.
It is used when a call to mrd_initialize_element(3mrd) is issued
against a medium changer that does not support the Initialize
Element Status command.
It is used when the medium changer does not support the Position
To Element command. The seven and five slot DLT loaders do not
support the command, though the TL820 and TL810 family libraries
do. Some models of TLZ6L and TLZ7L do not support the command and
may take a long time to fail.
It is used when the medium changer does not support the Ready
Inport command. The TL820 family of DLT libraries support this
command. The TL810 family of DLT libraries allows this command to
succeed, but it doesn't perform any function.
It is also used for a SCSI command failure, when the ASC is set
to one of:
o 0x1A - Parameter list length error
o 0x20 - Invalid command operation code
o 0x22 - Unsupported command
o 0x24 - Illegal field in CDB
o 0x25 - Logical unit not supported
o 0x26 - Threshold parameters not supported
o 0x28 - Import or Export element accessed
o 0x2C - Command sequence error
o 0x39 - Saving parameters not supported
o 0x3D - Invalid bits in Identify message
o 0x53 - Medium removal prevented
This status is also returned when the ASC and ASCQ are zero, but
the key is five (5).
27.4.7 – MRD_STATUS_ROBOT_ATTENTION
This error occurs when a SCSI command fails with the ASC set to
one of 0x29, 0x2A or 0x2F. The log_info contains the ASCQ. The
SCSI translations for these error codes are:
o 0x29 - Power-on, Reset or Bus device reset occurred
o 0x2A - Mode Parameters Changed
o 0x2F - Command cleared by another initiator
This error also occurs when the ASC and ASCQ are zero, but the
SCSI sense key is 6h.
27.4.8 – MRD_STATUS_DATA_PROTECT
This error is returned by mrd_scsi_decode(3mrd) when the asc and
ascq are zero, but the key value is seven (7).
27.4.9 – MRD_STATUS_BLANK_CHECK
This error is returned by mrd_scsi_decode(3mrd) when the asc and
ascq are zero, but the key value is eight (8).
27.4.10 – MRD_STATUS_VENDOR_UNIQUE_ERROR
This error occurs when the internal routine used to decode SCSI-
2 errors encounters an error that it has not been written to
antipicate.
This error also returned when the ASC is zero and the ASCQ is not
one of zero or six, and when ASC/ASCQ are both zero and the key
is 9h.
27.4.11 – MRD_STATUS_COPY_ABORTED
This error is returned by mrd_scsi_decode(3mrd) when the asc and
ascq are zero,
27.4.12 – MRD_STATUS_SENSE_EQUAL
This error is returned by mrd_scsi_decode(3mrd) when the asc and
ascq are zero, but the key value is Ch (12).
27.4.13 – MRD_STATUS_VOLUME_OVERFLOW
This error is returned by mrd_scsi_decode(3mrd) when the asc and
ascq are zero, but the key value is Dh (13).
27.4.14 – MRD_STATUS_MISCOMPARE
This error is returned by mrd_scsi_decode(3mrd) when the asc and
ascq are zero, but the key value is Eh (14).
27.4.15 – MRD_STATUS_SENSE_RESERVED
This error is returned by mrd_scsi_decode(3mrd) when the asc and
ascq are zero, but the key value is Fh (15).
27.4.16 – MRD_STATUS_ROBOT_COMM_ERROR
This error also occurs as the result of a SCSI command failure,
when the ASC is set to one of:
o 0x08 - Logical unit communcation errors.
o 0x43 - Message error
o 0x45 - Select or Reselect failure
o 0x47 - SCSI parity error
o 0x48 - Initiator detected error message received
o 0x49 - Invalid message error
o 0x4A - Command phase error
o 0x4B - Data phase error
o 0x4E - Overlapped commands attempted
o 0x54 - SCSI to host system interface failure
27.4.17 – MRD_STATUS_ROBOT_MECH_ERROR
This error occurs as the result of a SCSI command failure, when
the ASC is set to one of:
o 0x15 - Positioning error.
o 0x8B - Vendor unique; Pass-through mechanism errors on the
TL82n
27.4.18 – MRD_STATUS_AUTOCLEAN
This error occurs when a SCSI command fails with the ASC set
to 0x30 and the ASCQ set to 0x3. On TL8nn libraries supporting
Auto-clean, it indicates that a command was attempted while an
auto-clean was in progress.
27.4.19 – MRD_STATUS_CART_DAMAGED
This error occurs when a SCSI command fails with the ASC set
to 0x30, but the ASCQ is NOT a value of 0x3. The log_info will
contain the ASCQ.
27.4.20 – MRD_STATUS_ELEMENT_INVALID
This error occurs when a SCSI command fails with the ASC set to
0x21. The log_info will contain the ASCQ. This indicates that an
invalid element address reached the medium-changer. For example,
specifying the 13th slot when only 12 slots are present.
27.4.21 – MRD_STATUS_CART_NOT_AVAIL
This error can occur on the TL81n and TL82n family of DLT
libraries when the source of a move is a drive and the cartridge
in the drive is still on-line. These robots do not allow moving
the cartridge until the drive is taken offline.
27.4.22 – MRD_STATUS_DESTINATION_FULL
On routines that perform a SCSI Move Medium command, this error
indicates that the destination element already has a cartridge in
it.
27.4.23 – MRD_STATUS_SOURCE_EMPTY
On routines that perform a SCSI Move Medium command, this error
indicates that the source element is empty.
27.4.24 – MRD_STATUS_ROBOT_DOOR_OPENED
This occurs when a SCSI command fails with the ASC set to 0x80
and the ASCQ set to 0x0. On TL8nn libraries this typically
indicates that the cabinet door was opened during a command
operation.
27.4.25 – MRD_STATUS_DEVICE_INVALID
This error code is used when an OpenVMS system service fails with
the status SS$_NOSUCHDEV or SS$_IVDEVNAM. This will typically
occur in mrd_startup(3mrd) when the caller tries to open a device
which doesn't exist or uses an invalid device name.
This error also occurs when the routine is called on behalf of
a device controlled by the JU driver. The Media Robot Utility no
longer uses the JU driver.
27.4.26 – MRD_STATUS_ROBOT_NOT_READY
Under OpenVMS and Digital UNIX, this error occurs as the result
of a SCSI command failure, when the ASC is set to one of:
o 0x80 - When the ASCQ is not zero (0).
o 0x81 - Vendor unique; gripper errors on the TL82X and TL81X
o 0x04 - Logical unit not ready
o 0x3E - Logical unit has not been self configured
o 0x40 - Diagnostic failure; ASCQ indicates component
o 0x42 - Power-on self test failure
o 0x44 - Internal target failure
o 0x46 - Unsuccessful soft reset
o 0x4C - Logical unit failed self-configuration
This status is also returned when the ASC and ASCQ are zero, but
the key is two (2).
27.4.27 – MRD_STATUS_ROBOT_CMD_ABORTED
This error code is used when an OpenVMS system service fails with
the status SS$_ABORT.
27.5 – Related Functions
Functions:
o mrd_move_medium(3mrd)
o mrd_read_element_status(3mrd)
o mrd_startup(3mrd)
o mrd_position_to_element(3mrd)
o mrd_initialize_element(3mrd)
o mrd_ready(3mrd)
o mrd_prevent_allow(3mrd)