MSA_UTIL_HELP.HLB  —  ADD  UNIT  Qualifiers

1    /ADG

         Specifies the RAID type for the UNIT as Advanced Data Guard (ADG).

2    /CACHE

         Determines whether the controller's cache should be used for the
         UNIT. Caching is ON by default. To disable caching, use a /NOCACHE
         qualifier with SET UNIT or ADD UNIT commands.

3    /DISK

         Specifies the disk numbers to be used to form the UNIT. Multiple
         disks must be enclosed in parenthesis.

         Format:
                 /DISK=(disk numbers[,...])

         Note: The disk numbers for the existing disks can be obtained
               using the SHOW DISKS command.

4    /IDENTIFIER

         This is the user-defined identifier for the unit. This identifier
         is used by OpenVMS to name the device. The value of the identifier
         can be between 1- 9999

         Note: Identifier is not required for Smart Array Controllers.

         Format:
                 /IDENT= n

5    /JBOD

         Specifies the RAID type to be JBOD. This is also synonymous to
         RAID 0.

6    /PARTITION

         Specifies the partition number to be used for a given UNIT. The
         first unit that is created on a disk/disk group will automatically
         be assigned the partition number 0. The units that are subsequently
         created on this disk/disk group will need to be created with partition
         numbers in a sequential order.

         Format:
                 /PART=(partition_number)

7    /RAID_LEVEL

         Specifies the RAID type of the UNIT. The support values for this
         qualifier are 0, 1, 5, 50, and 60.

         -  RAID 0 is Data Striping
         -  RAID 1 is Disk Mirroring
         -  RAID 5 is Data Striping with Striped Parity
 	-  RAID 50 is Data Striping across RAID 5 arrays
 	-  RAID 60 is Data Striping across RAID 6 arrays

         Format:
                 /RAID=[(0 | 1 | 5 | 50 | 60)]

        Note:

        - When minimum four disks are supplied to create a RAID 1 unit,
          the controller creates a RAID 10 unit; which is Data Striping
          across RAID 1 arrays.

        - SHOW UNITS displays "Logical Volume Raid Level: RAID 1" for the
          RAID 10 units. If the data disks used by logical unit number (LUN)
          are more than two disks, the implementation of that LUN is
          RAID 10.

8    /SIZE

         Specifies the size of the UNIT. When the size qualifier is
         not specified, the size defaults to the Maximum capacity of
         the disks depending on the RAID level.

         Format:
                 /SIZE=#(Gb | Mb | Kb | %)

9    /SPARES

         Specifies the disk numbers to be used as spare disk(s). Multiple
         disks must be enclosed in parenthesis. Assigning a spare disk to
         an unit in a drive group will assign the spare disk to all the
         configured units in the drive group.

         If an unit is created on a disk group to which a spare disk is
         assigned, then the spare disk will be configured to the new unit
         (if it is not a RAID 0 unit). One spare disk can be assigned to
         multiple drive groups.

         Ensure that the size of the spare disk is at least equal to the
         size of the smallest drive in the drive group.

         Format:
                 /SPARE=(disk_number[,...])

         Note: The disk numbers for the existing disks can be obtained
               using the SHOW DISKS command.

10    /STRIPE_SIZE

          Specifies the stripe size for a given RAID volume. Stripe size
          must be one of 8, 16, 32, 64, 128, and 256 values. Raid 5 and ADG
          are limited to a maximum 64 KB stripes. RAID 0 and 1 default to 128
          KB stripes, and RAID 5 and ADG default to 16 KB stripes.
          SAS Smart Array Controllers with Firmware 5.0 onwards support
          512 KB stripe size with RAID5.

          Format:
                  /STRIPE=(stripe_size)

11    /VERBOSE

          Provides logging that can be interpreted by engineering.
Close Help