Writes events from one or more binary error log files to a single
new ASCII output file in an OpenVMS dump-style format.
Format
DUMP [input-file,...]
1 – Parameter
input-file
Supplies one or more names of binary error log files to be used
to produce an output dump file.
If you do not specify an input file, the default input file is
SYS$ERRORLOG:ERRLOG.SYS. If you do not specify a device and
directory, your current device and directory are used. If you
do not specify a file name, the default file name is ERRLOG. If
you do not specify a file type, the default file type is .SYS.
2 – Qualifiers
2.1 /BEFORE
/BEFORE[=date-time]
Specifies that only those events dated earlier than the stated
date and time are to be selected. Do not use /BEFORE with
/INVALID.
For date-time, you can specify an absolute time, a delta time, or
a combination of absolute and delta times. See the OpenVMS User's
Manual for details on specifying times.
If you omit a date and time, TODAY is used.
2.2 /ENTRY
/ENTRY[=keyword,...]
Specifies the range of entries to be selected. Do not use /ENTRY
with /INVALID.
You can specify one or both of the following keywords:
Keyword Description
START[:decimal- Indicates the start of a range of entries to
value] be selected.
END[:decimal- Indicates the end of a range of entries to be
value] selected.
Usage Notes:
o You can specify one or both of these keywords. If you specify
both keywords, you must enclose them in parentheses.
o If you specify /ENTRY without an entry range, the entry range
defaults to START:1,END:end-of-file.
o If you specify the START or END keyword without a value, the
keyword is ignored.
2.3 /EXCLUDE
/EXCLUDE=event-class[,...]
Specifies an event class or classes to be rejected. Do not use
/EXCLUDE with /INCLUDE.
For event-class, specify one or more of the keywords shown in
the following table. If you specify more than one keyword, use a
comma-separated list of values enclosed in parentheses.
Keyword Description
ATTENTIONS Reject device attention entries.
BUGCHECKS Reject all types of bugcheck entries.
CONFIGURATION Reject system configuration entries.
CONTROL_ENTRIES Reject control entries. Control entries
include the following entry types:
o System power failure restarts
o Time stamps
o System startups
o $SNDERR messages (system service to send
messages to error log)
o Operator messages
o Network messages
o ERRLOG.SYS created
CPU_ENTRIES Reject CPU-related entries. CPU entries
include the following entry types:
o SBI alerts/faults
o Undefined interrupts
o MBA/UBA adapter errors
o Asynchronous write errors
o UBA errors
DEVICE_ERRORS Reject device error entries.
ENVIRONMENTAL_ Reject environmental entries.
ENTRIES
MACHINE_CHECKS Reject machine check entries.
MEMORY Reject memory errors.
SNAPSHOT_ENTRIES Reject snapshot entries.
SYNDROME Reject firmware-generated entries that
describe a symptom set used by VSI support
personnel to identify problems.
TIMEOUTS Reject device timeout entries.
UNKNOWN_ENTRIES Reject any entry that has an unknown entry
class.
UNSOLICITED_MSCP Reject unsolicited MSCP entries.
VOLUME_CHANGES Reject volume mount and dismount entries.
2.4 /INCLUDE
/INCLUDE=event-class[,...]
Specifies an event class or classes to be selected. All other
event classes are implicitly rejected. Do not use /INCLUDE with
/EXCLUDE.
For event-class, specify one or more of the keywords shown in
the following table. If you specify more than one keyword, use a
comma-separated list of values enclosed in parentheses.
Keyword Description
ATTENTIONS Select device attention entries.
BUGCHECKS Select all types of bugcheck entries.
CONFIGURATION Select system configuration entries.
CONTROL_ENTRIES Select control entries. Control entries
include the following entry types:
o System power failure restarts
o Time stamps
o System startups
o $SNDERR messages (system service to send
messages to error log)
o Operator messages
o Network messages
o ERRLOG.SYS created
CPU_ENTRIES Select CPU-related entries. CPU entries
include the following entry types:
o SBI alerts/faults
o Undefined interrupts
o MBA/UBA adapter errors
o Asynchronous write errors
o UBA errors
DEVICE_ERRORS Select device error entries.
ENVIRONMENTAL_ Select environmental entries.
ENTRIES
MACHINE_CHECKS Select machine check entries.
MEMORY Select memory errors.
SNAPSHOT_ENTRIES Select snapshot entries.
SYNDROME Select firmware-generated entries that
describe a symptom set used by VSI support
personnel to identify problems.
TIMEOUTS Select device timeout entries.
UNKNOWN_ENTRIES Select any entry that has an unknown entry
class.
UNSOLICITED_MSCP Select unsolicited MSCP entries.
VOLUME_CHANGES Select volume mount and dismount entries.
2.5 /INTERACTIVE
/INTERACTIVE
/NOINTERACTIVE
Specifies whether or not ELV is to run in interactive shell mode
after you execute the ELV command. By default, interactive shell
mode results from the way the current ELV command was entered.
2.6 /INVALID
Specifies that invalid (rather than valid) events are to be
written to an output dump file. Do not use /INVALID with /BEFORE,
/ENTRY, /EXCLUDE, /INCLUDE, /[NO]NODE, /REJECTED, or /SINCE.
2.7 /LOG
/LOG
/NOLOG
Specifies whether or not ELV is to output control and
informational messages to the terminal. The default /NOLOG does
not output these messages to the terminal.
2.8 /NODE
/NODE[=node-name,...]
/NONODE[=node-name,...]
Specifies that events occurring on a node or nodes are to be
selected or rejected. Do not use /NODE or /NONODE with /INVALID.
If you enter /NODE without a value, only events that occur on the
node on which you are running ELV are selected.
If you enter /NONODE without a value, events occurring on all
nodes that are represented in the error log file are selected.
2.9 /OUTPUT
/OUTPUT[=output-file]
Specifies the output file that is to contain OpenVMS dump-style
records for events.
If you do not specify an output file name, the input file name is
used. If you do not specify a device and directory, your current
device and directory are used. If you do not specify a file type,
the default file type is .DMP.
2.10 /REJECTED
Specifies that rejected (rather than selected) events are to
be written to an output dump file. Do not use /REJECTED with
/INVALID.
2.11 /SINCE
/SINCE[=date-time]
Specifies that only those events dated later than the stated date
and time are to be selected. Do not use /SINCE with /INVALID.
For date-time, you can specify an absolute time, a delta time, or
a combination of absolute and delta times. See the OpenVMS User's
Manual for details on specifying times.
If you omit a date and time, TODAY is used.
3 – Examples
1.ELV> DUMP /NODE=DUMBO /ENTRY=END:10 ERROR_FILE.SYS,ERRLOG.SYS
The command in this example writes OpenVMS dump-style records
created from selected events in two input files, ERROR_FILE.SYS
and ERRLOG.SYS, to an output dump file named ERROR_FILE.DMP.
The name of the output file comes from the name of the first
input file in the list.
The selected events, which end with entry 10, are those that
occurred on node DUMBO.
2.$ ANALYZE/ERROR_LOG/ELV DUMP /INCLUDE=(DEVICE_ERRORS,TIMEOUTS) /LOG
The command in this example writes OpenVMS dump-style
records created from selected events in the default
SYS$ERRORLOG:ERRLOG.SYS file to an output dump file named
ERRLOG.DMP.
The selected events include only the DEVICE_ERRORS and TIMEOUTS
event classes. In addition, control and informational messages
are output to the terminal.
3.ELV> DUMP /SINCE=22-MAY-2003:01:00:00.00 /BEFORE=24-MAY-2003:04:51:33.87
The command in this example writes OpenVMS dump-style
records created from selected events in the default
SYS$ERRORLOG:ERRLOG.SYS file to an output dump file named
ERRLOG.DMP.
The selected events fall in the interval between the two
specified dates.
4.ELV> DUMP /SINCE=22-MAY-2003:01:00:00.00 /BEFORE=24-MAY-2003:04:51:33.87
/REJECTED
This example is identical to the previous example except that
rejected events are written rather than selected events.
The rejected events are those that fall outside the interval
between the two specified dates.
5.$ ANALYZE/ERROR_LOG/ELV DUMP /INVALID /OUTPUT=OUTFILE.OUT
The command in this example writes OpenVMS dump-style
records created from invalid events in the default
SYS$ERRORLOG:ERRLOG.SYS file to an output dump file named
OUTFILE.OUT.