DATA LINK PORT
Support: All
Name of the data link port used for this X.25 data adjacency. This
attribute is supported only if the owning routing circuit entity's
characteristic type is set to x25 da.
DTE ADDRESS
Support: All
DTE address of the neighboring node on an X.25 circuit. This status is
supported only if the owning circuit entity's characteristic type
is x25 da.
ENDNODE IDS
Support: All
System IDs of neighboring end nodes. This attribute is supported only
if the node is an end node and the owning circuit entity's
characteristic type is not x25 da.
ENDNODE NETS
Support: All
NETs computed from the system IDs in the endnode ids status and the
set of area addresses in the owning routing entity's manual area
addresses set. This attribute is supported only if the node is an
end node and the owning circuit entity's characteristic type is not
x25 da.
HOLDING TIMER
Support: L1,L2
Holding time for this adjacency, updated from the router-to-router
Hello messages. This attribute is supported only if both the node and
the adjacency are routers.
IP ADDRESSES
Support: IP
IP addresses of the neighbor node. If these are not known, the set is
empty.
LAN ADDRESS
broadcast circuit. This status is supported only if the owning
circuit entity's characteristic type is csma-cd.
LAN PRIORITY
Support: L1,L2
Priority of the neighbor of this adjacency for becoming the LAN level
1 designated router if the adjacency is a DECnet-Plus level 1 router
or the LAN level 2 designated router if the adjacency is a DECnet-Plus
level 2 router. This status is supported only if the owning circuit
entity's characteristic type is csma-cd; and the adjacency is a
router rather than an end node.
LEVEL
Support: L1,L2
The level of the adjacency. This attribute is supported only if both
the node and the adjacency are routers.
Level 1 - The adjacency is used for level 1 routing.
Level 2 - The adjacency is used for level 2 routing.
Level 1 & 2 - The adjacency is used for level 1 and level 2 routing.
Level 0 - The usage is undefined.
NEIGHBOR AREAS
Support: L1,L2
Area addresses of the neighboring node. This attribute is supported
only if both the node and the adjacency are routers and the owning
circuit entity's characteristic type is not x25 da.
NEIGHBOR NODE ID
Support: L1,L2
Node ID of the neighboring node.
NEIGHBOR NODE TYPE
Support: All
Type of the neighboring node. This status is supported only if the
owning circuit entity's characteristic type is not x25 da.
DECnet-Plus endnode - The node is a DECnet-Plus end node.
DECnet-Plus level 1 router - The node is a DECnet-Plus level 1 router.
DECnet-Plus level 2 router - The node is a DECnet-Plus level 2 router.
DECnet-Plus router - The node is a DECnet-Plus router.
non-dna router - The node is not a DNA router.
phaseiv endnode - The node is a Phase IV end node.
phaseiv level 1 router - The node is a Phase IV level 1 router.
phaseiv level 2 router - The node is a Phase IV level 2 router.
phaseiv router - The node is a Phase IV router.
unknown - The node type is unknown.
NEIGHBOR PROTOCOLS SUPPORTED
Support: IP
Network protocols supported by the neighboring node either IP or
ISO8473.
ROUTER NETS
Support: End
Network Entity Titles NETs of a neighboring router. This status is
supported only if the adjacency is a level 1 or level 2 router, and
the owning circuit entity's characteristic type is not x25 da.
STATE
Support: All
State of the routing circuit adjacency entity. May be one of the
following:
FAILED
INITIALIZING
UP
UP/DORMANT
TYPE
Type of adjacency.
AUTOCONFIGURED - Created by autoconfiguration.
MANUAL - Created manually by a create command.
This attribute indicates whether the adjacency has been manually
created, or whether the adjacency was created by means of hello PDUs.
It will always have the value manual when it has been created by the
create command; otherwise, it will have the value autoconfigured.