o  data link port

    Support: All

    Name of the data link port used for this X.25 data adjacency.
    This attribute is supported only if the owning routing circuit
    entity's characteristic type is set to x25 da.

 o  dte address

    Support: All

    DTE address of the neighboring node on an X.25 circuit.
    This status is supported only if the owning circuit entity's
    characteristic type is x25 da.

 o  endnode ids

    Support: All

    System IDs of neighboring end nodes. This attribute is supported
    only if the node is an end node and the owning circuit entity's
    characteristic type is not x25 da.

 o  endnode nets

    Support: All

    NETs computed from the system IDs in the endnode ids status and
    the set of area addresses in the owning routing entity's manual
    area addresses set. This attribute is supported only if the node
    is an end node and the owning circuit entity's characteristic
    type is not x25 da.

 o  holding timer

    Support: L1,L2

    Holding time for this adjacency, updated from the router-to-
    router Hello messages. This attribute is supported only if both
    the node and the adjacency are routers.

 o  ip addresses

    Support: IP

    IP addresses of the neighbor node. If these are not known, the
    set is empty.

 o  LAN address

    Data link address of the neighboring node on a broadcast circuit.
    This status is supported only if the owning circuit entity's
    characteristic type is csma-cd.

 o  LAN priority

    Support: L1,L2

    Priority of the neighbor of this adjacency for becoming the LAN
    level 1 designated router (if the adjacency is a DECnet-Plus level
    1 router) or the LAN level 2 designated router (if the adjacency
    is a DECnet-Plus level 2 router).

    This status is supported only if the owning circuit entity's
    characteristic type is csma-cd; and the adjacency is a router
    rather than an end node.

 o  level

    Support: L1,L2

    The level of the adjacency. This attribute is supported only if
    both the node and the adjacency are routers.

    Level 1      The adjacency is used for level 1 routing.

    Level 2      The adjacency is used for level 2 routing.

    Level 1 & 2  The adjacency is used for level 1 and level 2 routing.

    Level 0      The usage is undefined.

 o  neighbor areas

    Support: L1,L2

    Area addresses of the neighboring node. This attribute is
    supported only if both the node and the adjacency are routers
    and the owning circuit entity's characteristic type is not x25
    da.

 o  neighbor node id

    Support: L1,L2

    Node ID of the neighboring node.

 o  neighbor node type

    Support: All

    Type of the neighboring node. This status is supported only if
    the owning circuit entity's characteristic type is not x25 da.

    non-dna        The node is not a DNA router.
    router

    phase iv       The node is a Phase IV end node.
    endnode

    phase iv       The node is a Phase IV level 1 router.
    level 1
    router

    phase iv       The node is a Phase IV level 2 router.
    level 2
    router

    DECnet-Plus    The node is a DECnet-Plus end node.
    endnode

    DECnet-Plus    The node is a DECnet-Plus level 1 router.
    level 1
    router

    DECnet-Plus    The node is a DECnet-Plus level 2 router.
    level 2
    router

    DECnet-Plus    The node is a DECnet-Plus router.
    router

    unknown        The node type is unknown.

    phase iv       The node is a Phase IV router.
    router

 o  neighbor protocols supported

    Support: IP

    Network protocols supported by the neighboring node (either IP or
    ISO8473).

 o  router nets

    Support: End

    Network Entity Title(s) (NETs) of a neighboring router. This
    status is supported only if the adjacency is a level 1 or level
    2 router, and the owning circuit entity's characteristic type is
    not x25 da.

 o  state

    Support: All

    State of the routing circuit adjacency entity. May be one of the
    following:

    failed
    initializing
    up
    up/dormant

 o  type

    Type of adjacency.

    autoconfigured Created by autoconfiguration.

    manual         Created manually by a create command.

    This attribute indicates whether the adjacency has been manually
    created, or whether the adjacency was created by means of hello
    PDUs. It will always have the value manual when it has been
    created by the create command; otherwise, it will have the value
    autoconfigured.