set [node node-id] routing circuit circuit-name -
reachable address simple-name ...
Modifies attributes of a routing circuit reachable address entity
which contains information about a manually entered address prefix
accessible over that circuit. It exists only on L2 routers and
end nodes. The modifiable routing circuit reachable address
attributes and their data types [in brackets] are:
block size [integer]
cost [integer]
data format [PhaseIV or Phasev]
DTE addresses [set of dte addresses]
ISDN address [isdn-address]
LAN address [id]
metric type [metric-type]
mapping [string]
modem addresses [modem-address]
modem address prefix [modem-address-prefix]
modem address suffix [modem-address-suffix]
permitted lan address [lan-address]
type [string]
1 – block_size
Support: End, type outbound
Default: 0 Value: 0-65536
The data link block size to be used for this prefix.
For an end system, the data link block size to be used for this
prefix. If the block size is set to the default, the manual
block size of the circuit will be used instead. This attribute
is supported only if the type characteristic is set to outbound.
set [node node-id] routing circuit circuit-name -
reachable address simplename block size integer
Example:
set routing circuit csmacd-1 -
reachable address to-area4 block size 500
2 – cost
Support: L2
Default: 20 Value: 1-63
Cost of reaching this address prefix over this circuit.
3 – data_format
Support: L2
Default: PhaseV Value: PhaseIV (1) or PhaseV (0)
The PDU data format to be used when forwarding data (or
error report) NPDUs using this reachable address.
This attribute is supported only if the type characteristic
is set to outbound. You can modify this characteristic only
when the entity is disabled.
4 – dte_addresses
Support: End,L2
Default: No DTE addresses={ } Value: Set of DTE addresses
A set of DTE addresses to which a call may be directed in order
to reach an address that matches the address prefix of this
reachable address.
This characteristic is supported if the node is a level 2 router,
where the owning circuit's characteristic type is one of the X.25
circuit types, and the reachable address's characteristic type
is outbound. It is also supported by end nodes operating over an
x25 da circuit. You can modify this characteristic only when the
entity is disabled.
set [node node-id] routing circuit circuit-name reachable -
address simplename dte address {dte-address[dte-address...]}
Example:
set routing circuit x25_circuit-1 reachable address ughh_v -
dte address { 2267643 }
5 – ISDN address
Support: L1,L2
Default: { } Value: Set of ISDN addresses
A full set of E.164 ISDN network addresses that a call may be
directed in order to reach a network number that matches the
address prefix of the parent reachable address entity. Associated
with each ISDN network address, but not visible to Network
Management, is a variable last failure of type binary absolute
time. This attribute is supported only if access type is ISDN DA.
6 – LAN address
Support: L2,End
Default: 00-00-00-00-00-00 Value: ID
A single LAN address to which an NPDU can be directed in order
to reach an address that matches the address prefix of the parent
reachable address entity. This attribute is supported only if the
type characteristic is set to outbound on broadcast circuits only.
A valid address is required here.
You can modify this characteristic only when the entity is
disabled.
set [node node-id] routing circuit circuit-name reachable -
address simplename lan address aa-00-04-00-xx-xx
Example:
set routing circuit csmacd-1 reachable address to-area4 -
lan address aa-00-04-00-12-34
7 – mapping
Support: End,L2
Default: X.121 Value: Manual or X.121
Type of mapping used to determine the SNPA address to which a
call should be placed for this address prefix. You can modify
this characteristic only when the entity is disabled. If the
circuit is a broadcast circuit, this attribute must have the
value manual.
manual The mapping uses the set of addresses in the
characteristic dte addresses or the address in the
characteristic LAN address.
X.121 The mapping uses the X.121 address extraction algorithm.
This characteristic is supported only if either of the following
conditions is satisfied:
o The node is a level 2 router or an end node, and the owning
circuit's characteristic type is one of the X.25 circuit
types; or
o The node is a level 2 router, the owning circuit's
characteristic type is csma-cd, and the reachable address's
characteristic type is outbound.
set [node node-id] routing circuit circuit-name reachable -
address simplename mapping manual_or_x.121
Example:
set routing circuit csmacd-1 reachable address to-area4 -
mapping manual
8 – metric_type
Support: L2
Default: Internal Value: Internal, external
The metric type of the cost metric for the circuits. If internal,
the I/E bit for the metric in the Prefix Neighbors option of
L2 LSPs is set to 0, otherwise (external) is set to 1.
9 – modem_addresses
Support: L1,L2
Default: { } Value: Set of modem addresses
A set of full dial sequence that contains the address (PSTN or
ISDN) to which a call may be directed in order to reach a
network number that matches the address prefix of the parent
reachable address) entity. Associated with each modem address,
but not visible to Network Management, is a variable last
failure of type binary absolute time. This is valid only if
mapping is manual and the parent circuit entity's access time
is Modem DA.
10 – modem_address_prefix
Support: L1,L2
Default: L1,L2 Value: Address string
The address that is to be inserted to the beginning of the address
extracted from the NSAP address. This is valid only if mapping is
not manual and the parent circuit entity's access type is Modem
DA. It is used in conjunction with modem access suffix to form the
complete dial sequence.
11 – modem_address_suffix
Support: L1,L2
Default: L1,L2 Value: Address string
The address that is to be inserted to the end of the address
extracted from the NSAP address. This is valid only if mapping
is not manual and the parent circuit entity's access type is
Modem DA. It is used in conjunction with modem access prefix
to form the complete dial sequencence.
12 – permitted LAN address
Support: End
Default: { } Value: Set of LAN addresses
The set of LAN addresses corresponding to routers that are
permitted to be used for forwarding to this prefix. This
attribute is supported only if the type characteristic is
set to filter on broadcast circuits only. The default is
an empty set, and at least one LAN address is required.
set [node node-id] routing circuit circuit-name -
reachable address simplename -
permitted lan address {lan-address[,lan-address...]}
Example:
set routing circuit csmacd-1 reachable address to-area4 -
type filter, -
permitted lan address {aa-00-04-00-23-45,aa-00-04-00-BC-DE}
13 – type
Support: L2,End
Default: Outbound Value: Inbound, outbound, or filter
Type of the reachable address. You can modify this characteristic
only when the entity is disabled.
inbound For L2 only, the address prefix corresponds to a
Phase IV area that is reachable through this node
and circuit by inbound traffic.
outbound The address prefix is in an external domain
that is reachable over this circuit by outbound
traffic.
filter The address prefix defines a set of addresses that
should be reached via the set of routers listed in
the permitted LAN address characteristic.
set [node node-id] routing circuit circuit-name -
reachable address simplename -
type reachable-addr-type
Example:
set routing circuit csmacd-1 -
reachable address to-area4 type filter