1  STOP
 

2  IP_INTERFACE
   Directs PEdriver to stop using the specified IP interface.

                                CAUTION

      If you use STOP IP_INTERFACE to stop the only connection
      you have to a cluster, it results in a system CLUEXIT. If
      you use STOP IP_INTERFACE to stop the only the connection,
      connected to a cluster, the system will CLUEXIT even when
      you have another connection that uses a different cluster
      port. However, if you stop all the IP_INTERFACE results in
      excessive activity. When PEdriver loses access to all of
      its IP interfaces, it makes an effort to restore cluster IP
      interfaces communications by completely re-initializing
      itself. After the displayed retry count is exceeded,
      PEdriver permanently goes offline. To disable cluster use
      of all but one IP interface, enter the following command:
      SCACP> STOP IP_INTERFACE * /EXCLUDE=ipinterface

      All IP interfaces are stopped except the excluded interface
      and PEdriver does not need to be reset.

   Format

     STOP IP_INTERFACE  ipinterface[,...]
 

3  Parameter
 

ipinterface[,...]

   Includes specific IP interface, which you can use wildcards to
   specify.

   o  Use the /EXCLUDE qualifier to exclude IP interfaces.

   o  Use the SHOW IP_INTERFACE command to display IP interface
      names.
 

3  Qualifiers
 

/EXCLUDE

      /EXCLUDE=(ipinterface[,...])

   Excludes specific IP interface, which you can use wildcards to
   specify.
 

3  Example

 SCACP> STOP IP_INTERFACE WE0

     This command stops PEdriver on the IP interface WE0.
 

2  LAN_DEVICE
   Directs PEdriver to stop using the specified LAN device. The
   original (and still supported) way to stop PEdriver on a LAN
   device is SYS$EXAMPLES:LAVC$STOP_BUS.

                                CAUTION

      If you use either STOP LAN_DEVICE or SYS$EXAMPLES:LAVC$STOP_
      BUS to stop the only connection you have to a cluster, you
      cause the system to CLUEXIT.

      Even when you have have another connection using a
      different cluster port, stopping all LAN devices results
      in excessive activity. When PEdriver loses access to all
      of its LAN devices, it makes an effort to restore cluster
      communications by completely re-initializing itself.

      After the last LAN device is stopped, the reinitilization
      produces an error message similar to the following:

          SCACP> STOP LAN *
          ;%PEA0, Port is Reinitializing ( 49 Retries Left). Check the Error Log.

      After the displayed retry count is exceeded, PEdriver
      permanently goes offline.

      To disable cluster use of all but 1 LAN device, enter the
      following command:

          SCACP> STOP LAN * /EXCLUDE=landevicename

      All LAN devices except the excluded device are stopped, and
      PEdriver does not need to be reset.

   Format

     STOP LAN_DEVICE  landevicename
 

3  Parameter
 

landevicename[,...]

   Includes specific LAN devices, which you can use wildcards to
   specify.

   Use the /EXCLUDE qualifier to exclude LAN devices.

   Use the SHOW LAN_DEVICE command to display device names.
 

3  Qualifier
 

/EXCLUDE

      /EXCLUDE=(landevicename[,...])

   Excludes specific LAN devices, which you can use wildcards to
   specify.
 

3  Example

 SCACP> STOP LAN_DEVICE EWA

     This command stops PEdriver on the LAN device EWA.
 

2  TRACE
   Stops PEDRIVER tracing. You can read the trace data recorded so
   far with a SHOW TRACE command.

   To revert trace behavior to initial settings, enter the command
   SET TRACE/DEFAULT.

                                  NOTE

      This command is reserved for use by VSI Services and OpenVMS
      Engineering only. Trace commands and output are subject to
      change from release to release.

   Format

     STOP TRACE
 

3  Parameters
   None.
 

3  Qualifiers
   None.
 

3  Example

 SCACP> STOP TRACE

     The command in this example stops PEDRIVER tracing.