1 SHOW 2 CONTROLLER Displays information about the SAS Controller. Format SHOW CONTROLLER [device_name] 3 Parameters device_name: (OPTIONAL) The device name is an SAS device name used to display information about a specific controller. The device name has the format ddcu, where: dd is the device code. c is the controller designation A through Z. u is the unit number (0 through 9999). If you do not specify a device name, all controllers are displayed. 3 Qualifiers /DEFAULT Displays information about the default controller. /FULL Displays additional information about the SAS Controller. 3 Example SAS> SHOW CONTROLLER A default controller is not set. All matching controllers displayed. Adapter: _PKA0: Controller Type : SAS LSISAS1068 Firmware version : 1.10.0.0 SAS WWID : 500605B0-00001A20 RAID Capabilities RAID 0 (Integrated Striping) supported. RAID 0+1 (Integrated Mirroring Enhanced) supported. RAID 1 (Integrated Mirroring) supported. Active IR Volumes : 1 of 2 Active PHYS disk : 3 of 10 Cache: Not Available. Battery: Not Available. This example shows SAS Controller information. 2 DISK Displays a table of available SAS, SATA, and IR volumes in the SAS Controller. Each column in the table is displayed as follows: Volume Description ID SAS ID for SAS/SATA device. RAID volume ID for RAID volume set. Enc Enclosure number: o Direct attached is displayed as "DA." o Non-direct attached shows the enclosure handle number. PHY SAS PHY number of the physical disk. Slt Physical slot or element index in the enclosure where the target device is physically located. Device OpenVMS device name. Type Device type. Size Disk size in MB. SAS SAS address (World Wide Identifier) of the device. Address Product Product model of the disk. Name Format SHOW DISK [sas_id] 3 Parameters sas_id The SAS ID is the ID shown when you enter the SAS command SHOW DISK. If you do not enter a SAS ID, the SAS utility displays all available physical SAS disks. 3 Qualifiers /FULL Displays additional information about disks. 2 ENCLOSURE Displays information about the SAS enclosure connected to the SAS Controller. Format SHOW ENCLOSURE [encl_id] 3 Parameters encl_id Displays information about a specific SAS enclosure. If the enclosure ID is not specified, the SAS utility displays information about all available enclosures that the SAS Controller finds. 3 Qualifiers /FULL Displays additional information about SAS enclosures. 3 Example SAS> SHOW ENCLOSURE Enclosure 1 Encl WWID : 500605B0-00001A20 Num slots : 8 Start slot : 1 Encl Flags SEP BUS/Target ID is not valid. Start BUS/Target ID is not valid. IOC (direct attached) SGPIO. This example shows information about internal Enclosure 1 connected to the SAS Controller. 2 EXPANDER Displays information about the SAS expander connected to the SAS Controller. Format SHOW EXPANDER [exp_id] 3 Parameters exp_id Displays information about a specific SAS expander. If an expander ID is not specified, the SAS utility displays all available SAS expanders that the SAS Controller finds. 3 Qualifiers /FULL Displays additional information about the expanders in the SAS domain. 3 Example SAS> SHOW EXPANDER Expander 1 Physical Port : 0 SAS WWID : 500508B3-00A1396F Dev Handle : 9 Num PHYs : 13 SAS Level : 1 Exp Flags Device has configurable route table. Prog Link Rate Max 3.0Gbps Min 1.5Gbps HW Link Rate Max 3.0Gbps Min 1.5Gbps PHY Info Table Routing 3.0Gbps speed Att Dev Info SMP Target LSI Device This example shows information about external SAS Expander 1, which is connected to the SAS Controller. 2 PHY Displays SAS PHY information for all connections in the SAS Controller. Format SHOW PHY [phy_id] 3 Parameters phy_id Display information about a specific SAS PHY ID. (Use the SAS command SHOW DISK to display SAS PHY IDs.) If a PHY ID is not specified, the utility displays all available PHYs on the SAS Controller. 3 Qualifiers /ERROR Displays SAS PHY error counters. /FULL Displays additional information about the PHYs. 3 Example SAS> SHOW PHY 0 PHY 0 OwnerDev : 1 SAS WWID : 5000C500-003306B1 DevHandle : 9 PhyIdentifier : 0 Device Info SSP Target Direct Attached Flag SGPIO DA Enclosure present. PHY Info 3.0Gbps speed SAS> This example shows the SAS PHY connection for PHY 0. 2 UNIT Displays the IR volumes configured in the SAS Controller. Format SHOW UNIT [volume_id] 3 Parameters volume_id Displays information about a specific IR volume. If a volume ID is not specified, the SAS utility displays all available IR volumes that the SAS Controller finds. 3 Qualifiers /FULL Displays additional information about IR volumes. 3 Example SAS> SHOW UNIT IR Volume information: -------------- IR Volume 4 -------------- Volume Type : RAID 1 (LSI Logic Integrated Mirror) Volume State : Optimal Size : 69495 MB / 142325760 blocks IR Disk 1 Source Disk Disk State : Online Slot ID : 1 SAS WWID : 5000C500-0134CB8D IR Disk 0 Secondary Disk Disk State : Online Slot ID : 7 SAS WWID : 5000C500-0134DBB5 IR Hot Spare 7 Hot Spare Status : Active Slot ID : 6 SAS WWID : 12210000-06000000 This example displays volume information and all physical disks corresponding to the IR volume set. 2 VERSION Displays the version number of the SAS utility that you are currently using. Format SHOW VERSION 3 Example SAS> SHOW VERSION SAS$UTIL Version 1.0 Build 05-May-2006 This example shows that this version of the SAS utility is 1.0.